What the symptoms usually mean
- One cracked or broken board, rest of the floor firm: usually impact damage, for example from a dropped pallet. A board repair is reasonable.
- A dip or sag in one area, often near the tandems or the landing gear: suspect bent or failed cross members under it.
- Soft, spongy boards over a wide area: water has been getting in, and the steel below has probably been wet for a while too.
- Rust stains or flakes coming up through board seams: the cross members are rusting from the inside out.
- Floor that moves when a forklift crosses it: take it out of service until it has been looked at.
What most repair guides cover, and what they leave out
The guides we read from trailer shops and parts sellers explain board replacement well: empty the trailer, cut the damaged board between cross members, fit a new one, use three screws per cross member, caulk the joint and stagger the butt joints. That is good advice for a cracked board. The ones we looked at do not say when to repair or replace a cross member, or how to tell if the steel is the real problem. That is the part that decides whether the repair lasts.

Inspect from underneath first
Get the trailer safely supported and look at the underside, not just the top of the floor. Check:
- Each cross member for bends, flat spots and dents where it has been pushed up or down.
- The welds where cross members meet the main beams. Cracks here often show as a thin dark line with rust at the ends. Bright metal inside a crack means it is still moving.
- Rust that has flaked in layers. If a screwdriver or hammer tap goes through the steel, or it sounds soft, it has lost its strength.
- Areas near the landing gear and suspension hangers, where loads concentrate. See our guides on landing gear repair and cracked suspension hangers.
- The main beams themselves, and the edge rails that carry the floor.
Mark every problem with chalk or paint. The ones you can see easily are rarely the only ones.
Repair or replace the cross member?
Our rule of thumb is simple:
- Cracked weld, steel otherwise thick and sound: the crack is ground out and re-welded, often with a reinforcing plate. See cracked trailer cross member repair.
- Bent but not cracked: sometimes it can be straightened, but if it has been bent more than once the metal is tired and replacement is safer.
- Rusted thin, pitted or flaking: cut it out and weld in a new member. Welding onto thin rusty steel does not hold.
- Several in a row bad: look at why. Water getting in or an overloaded area will kill the new ones too.

The right order for the job
- Empty the trailer and support it safely.
- Lift the affected floor boards, or the whole section if the damage is spread out.
- Clean the steel to bare metal so cracks and thin spots show.
- Mark and fix the steel: weld cracks, cut out and replace bad cross members. See trailer welding & fabrication.
- Coat the steel before anything goes back on. You will not reach it again for years.
- Fit the new floor, with a bead of sealant between board and steel and staggered joints.
- Check the floor sits flat and the trailer is square before loading.
Why the steel fails: causes you can fix
- Water: leaking roof seams or side panels let water soak the floor and steel. Fixing the leak matters as much as the floor. See roof & side panel repair.
- Road salt: it sits against the underside through winter. Our winter salt corrosion checklist shows how to rinse and inspect.
- Point loads: heavy pallets or forklift axles repeatedly crossing the same spot.
- Old repairs: patches welded over rust that kept corroding.
Is it worth repairing an older trailer?
Sometimes the floor repair costs more than a tired trailer is worth, and sometimes it is the cheapest way to keep a sound frame earning. What decides it is the frame, not the floor. If the main beams and hangers are in good shape, new cross members and a new floor usually make sense. If the beams are rusted or the frame is out of square, think harder. We will tell you honestly which side of the line a trailer is on once we see it.
On-site or in the yard?
Our mobile truck brings MIG, stick and plasma with its own generator, so many cross member repairs can be done where the trailer is parked, without a tow. Opening up a long stretch of floor may need a flat clear area and more than a day. Read how we work on the mobile trailer welding page, and check the Brampton, Mississauga and Vaughan pages for coverage.
How to photograph the floor for a quote
- A wide shot of the inside of the trailer, showing the sag if you can.
- Close-ups of broken boards and board seams with rust stains.
- Photos of the underside: each cross member and weld, with a pen next to it for scale.
- Trailer length, where it is parked, and how soon it needs to be back on the road.
Send them to WhatsApp 437-985-7311. We give a quote from the photos before work begins.
Where we work
We are based at 115 Orenda Rd in Brampton and work in Mississauga, Toronto, Vaughan, Milton, Oakville and Caledon. Hours are 7 AM to 7 PM, seven days a week, with no overnight service.
Call 437-985-7311 WhatsApp photos
Frequently asked questions
Can I just replace the damaged floor boards on my dry van?
If only one or two boards are cracked, for example from a dropped pallet, and the cross members under them are sound, replacing those boards is a normal repair. If the floor sags, feels soft over a wide area, or the steel underneath is rusted or cracked, boards alone will not fix it.
Why does my dry van floor sag between the wheels and the landing gear?
Sag usually means the cross members under that area have bent, cracked at the welds, or rusted thin, or their connection to the main beams has failed. Wet cargo, salt and heavy forklift loads speed this up. Have it checked before the next heavy load.
Is it safe to keep running a trailer with a sagging floor?
We would not. A floor that moves can let a forklift or a heavy pallet break through, and failing cross members can get worse quickly. Take it out of service, or at least keep loads light, until someone has looked underneath.
Can you repair dry van cross members on-site?
Often yes. Our mobile welding truck can cut out and weld in cross members at your yard, 7 AM to 7 PM, seven days a week. Opening up a long section of floor may need more room and time, and we tell you which it is once we see photos.
How much does dry van floor and cross member repair cost?
It depends on how many cross members are bad, how much flooring has to come up and the trailer length, so we do not quote without seeing it. Send photos to WhatsApp 437-985-7311 and we will give you a quote before work starts.
Do you do the wood flooring too, or just the steel?
Our work is the welding: cross members, beams and hangers. If the floor boards also need replacing, tell us when you send photos so we can plan the job around it.
Related guides
More Baaz Welding guides · Cracked trailer cross member · Landing gear repair