Signs the deck needs work
- Soft spots or boards that flex when you walk on them, especially near the edges and over cross members.
- Rot, splits or missing pieces, and boards that have lifted at the ends.
- Loose, missing or rusted-through fasteners, and heads that have pulled below the surface.
- Rust streaks coming through the seams between boards. That usually means the steel below is wet and rusting.
- A deck that no longer sits flat, which can point to a bent or failed cross member rather than a wood problem.
Patch the boards, or redo the deck?
Most online guides cover this part well: replace a few boards when the damage is isolated and the rest is firm, and redo the whole deck when rot is widespread. Drivers on trucking forums repeat one warning, which is that patching piece by piece often leads to more repairs. We agree with that when the rot is spread across the deck, and we would add one test: if the steel under the bad boards is in good shape, patching is fine. If it is not, redo the steel before anything else.

The part most guides skip: the steel under the deck
Guides on deck replacement usually say to stay away from the cross members while cutting out old boards. They rarely say what to do if the cross members themselves are the problem. Once the boards are off, you can see things you cannot see from above:
- Cracks at the weld where a cross member meets the main beam. Shiny metal inside a crack usually means it is still moving. See our guide on cracked trailer cross members.
- Rust that has flaked in layers or pitted deep. If a screwdriver goes through or the steel sounds soft when tapped, welding on top will not hold.
- Bent or twisted members from overloading or forklift loads.
- Damage to neighbours. The deck also helps hold the cross members in place, so a failing deck often goes with cracks nearby.
- Suspension hangers and landing gear mounts close to the work. Read about cracked suspension hangers and landing gear repair or replace.
Fixing the steel with the deck off is far easier than doing it afterwards, so this is the cheapest moment to do it.

The right order for the job
- Strip the bad boards and remove old fasteners. Rusted screws often snap, so expect to grind or drill some out.
- Clean the steel to bare metal so you can see cracks and judge thickness.
- Mark every problem on the cross members and beams. Do not trust only the obvious ones.
- Weld, reinforce or replace the steel. Cracks are ground out and welded, and members rusted thin are cut out and replaced. See trailer welding & fabrication.
- Coat the steel before the wood goes on, because you will not get at it again for years.
- Fit the new decking and fasten it so water can drain and the boards are not trapped against bare steel.
- Check the deck sits flat and the trailer sits square before it goes back to work.
Wood decking and steel decking
Common deck materials are hardwoods such as oak and apitong, treated pine, and steel plate. Hardwood is the usual choice for heavy hauling, treated softwood costs less and wears faster, and steel does not rot but needs good coating and drainage. Which one suits you depends on what you haul and how the trailer is used. What does not change is that every wood deck sits on steel that has to be sound.
Weld on the deck, or fasten it down?
Some owners weld steel deck plate or angle iron to hold the boards, others bolt things so they can come off later. A removable setup is easier to repair next time. If you are not sure which suits your trailer, ask before you weld, because welds on a deck are hard to undo.
On-site or in the yard?
Because our welding truck comes to you, many cross member and weld repairs can be done where the trailer is parked, without towing. A full strip, steel rebuild and re-deck of a long trailer may need a clear flat yard area and more than a day. Our mobile trailer welding page covers how we work, and the Brampton, Mississauga and Vaughan pages list where we travel.
Buying a used flatbed with a bad deck
A shot floor can make a used trailer look like a bargain. Before you buy, look under the deck: cross member welds, rust, hangers and frame. A deck problem on top of steel problems is a very different cost from a deck problem alone. If you want a second opinion, send photos before you commit.
How to keep a deck lasting longer
- Keep drain gaps open and clean out debris.
- Rinse salt off the underside in winter. Our winter salt corrosion checklist has the routine.
- Spread heavy point loads and forklift traffic.
- Replace single damaged boards early, before water gets to the steel.
How to photograph a flatbed for a quote
- A wide shot of the whole deck.
- Close-ups of soft, broken or missing boards.
- If the boards are already off, shots of each cross member and weld, with a pen beside it for scale.
- Trailer length and type, and where it is parked.
Send them to WhatsApp 437-985-7311. We quote from the photos before work begins.
Where we work
We are based at 115 Orenda Rd in Brampton and work in Mississauga, Toronto, Vaughan, Milton, Oakville and Caledon. Hours are 7 AM to 7 PM, seven days a week, with no overnight service.
Call 437-985-7311 WhatsApp photos
Frequently asked questions
Can I replace just the soft boards on my flatbed deck?
If the cross members and frame under those boards are sound and the rest of the deck is solid, replacing individual boards is a reasonable repair. If several boards in a row are soft, or the steel underneath is rusted or cracked, patching usually brings you back for the same job a few months later.
What should I check before putting new decking on?
With the old boards off, check every cross member for cracks at the welds, rust that has pitted or flaked in layers, and bends. Also check the main beams, the outriggers or stake pockets, and the area around the landing gear and suspension hangers. Fix the steel first, because new wood on bad steel does not last.
Does the deck add strength to the trailer?
On many flatbeds the deck helps hold the cross members in place and spreads load across the frame. When the deck rots, the cross members and their welds can take more stress than they were designed for, which is one reason cracks show up around old, soft floors.
Can you do flatbed deck and cross member repair on-site?
Cross member repairs and welded repairs are often done in your yard with our mobile welding truck, 7 AM to 7 PM, seven days a week. A full strip, rebuild and re-deck can be a bigger yard job. We tell you which it is when we see photos.
How much does flatbed deck repair cost?
It depends on how many cross members are bad, how much of the deck is going, and the trailer length, so we do not quote a number without seeing it. Send photos to WhatsApp 437-985-7311 and we will give you a quote before work starts.
Should I buy a used flatbed with a bad deck to fix up?
Only after someone has looked under the deck. A rotted floor can be cheap to fix, or it can hide rusted cross members, cracked hangers and a tired frame. Have the steel looked at before you buy, not after.
Related guides
More Baaz Welding guides · Cracked trailer cross member · Landing gear repair